BOOST COOLER
FEATURES
AT A GLANCE
- Electronically controlled 2D injection by means of boost pressure and exhaust gas temperature
-
ProLine Version: High-quality steel braided lines and connection technology
- Display of boost pressure, exhaust gas temperature and boost cooler injection quantity.
- More power and torque of up to 10-25% possible
- Reduction of specific fuel consumption of up to 5-15
- Successfully tested by the renowned National Renewable Energy Laboratory (NREL)
- Dual Stage technology for maximum efficiency in all load ranges
- Effective intake air cooling, compensation of power losses at higher outside temperatures
- Reduction of nitrogen oxide formation & carbon emission with full load acceptance, ideal add-on to DPF.
- Deposit free combustion chamber and air intake, without formation of carbon.
- Einfache Installation
SNOW PERFORMANCE
BOOST COOLER
SYSTEME
The up-to-date digital 2D control unit was designed to reduce the specific fuel consumption in almost all load ranges.
The MPG-MAX control unit variably controls a small boost cooler nozzle through the entire power curve. This increases the combustion efficiency which in turn results in more power, without the increased fuel consumption.
The MPG-MAX system has a second output to control another, larger nozzle with a separate mapping ("Power Mode"). The activation point of the second nozzle can be adjusted individually to achieve the best performance results. The net effect is smooth power in all engine load states with no combustion quench.
STAGE 3 TD
CONTROLLER
The award-winning Boost Cooler Stage 3 turbo diesel control unit from SNOW Performance regulates the water or water-alcohol injection quantity progressively to the boost pressure and the exhaust gas temperature. The desired start and full injection times are simply entered in the enclosed LCD screen. The controller then generates a 2D injection curve for the optimum injection quantity in all load ranges. By using boost pressure and the exhaust gas temperature, the Stage 3 controller enables very precise water-methanol injection quantity regulation, especially in towing operation (trailer operation, motorhomes, trucks, etc.).
In addition to the primary injection nozzle, another nozzle, independent of the primary nozzle, is optionally controlled by the control unit. - This ensures optimal use of cooling and power in all load ranges of the turbo diesel.
The progressive injection of water or water/methanol based on the 2D mapping created is very precise and has a positive effect on cooling and engine performance over the widest possible engine load range.
PERFORMANCE
With the Boost Cooler, you can achieve a power increase of about 10-25%, even with already tuned turbo and supercharged engines. The optimum cooling compensates for typical power losses at higher outside temperatures. In addition, deposits in the combustion chamber and intake tract are reduced.
OPTIMAL COOLING
In contrast to a conventional intercooler, the charge air can be lowered below the ambient temperature! In addition to the outstanding efficiency, there is no loss of boost pressure as with conventional performance intercoolers.
The Boost Cooler efficiently cools the intake air and combustion chamber temperature ("in-cylinder-cooling"). The addition of alcohol (preferably methanol or inexpensive bio-ethanol) additionally increases efficiency and counteracts lean running.
DUAL STAGE
TECHNOLOGY
The controller has a 2nd output to control a further, larger nozzle with a separate mapping ('Power Mode'). The connection of the 2nd nozzle can be set individually to achieve the best possible performance results.
Temperature and pressure resistant Boost Cooler steel flex braided line - ProLine Series. High-quality steel braided line for your Boost Cooler water injection of the ProLine series. - There is hardly a better line for use in water-methanol injection systems. Steel flex lines from SNOW Performance are quality products at the highest level.
Ideally suited for high demands on appearance and safety, in motor sports as well as marine and aviation applications.
LESS CONSUMPTION -
LESS CO2
The better efficiency improves fuel economy. As a rule, fuel savings are in the range of 5-15% depending on the vehicle, driving style and use (e.g. tractors).
The NREL test result clearly shows that NOx emissions are significantly reduced with the Boost Cooler System activated. As a positive side effect, the DPF regeneration cycles are extended due to the lower pollutant emissions.
LESS DEPOSITS IN THE COMBUSTION CHAMBER
The combustion chamber of your engine remains free of deposits, the heat dissipation, e.g. at the exhaust valves, remains optimal.
Oil coking is reduced and prevented.
EASY INSTALLATION
To ensure a smooth installation, all connection materials are included in the scope of delivery of the system. The detailed installation instructions in German, with many illustrations and a clear structure, guide you step by step through the installation process.
MOTORSPORTS KNOW-HOW
As an OE supplier and through its activities in a wide range of motorsport areas, SNOW Performance proves the quality and durability of the high-quality water injection systems "Made by SNOW PERFORMANCE".
Pressure Diaphragm Pump
SNOW Performance 300 PSI UHO methanol injection pumps offer unmatched pressure, technology and reliability. All 300 PSI pumps are made in the USA and individually tested before shipping to ensure quality and reliability. Although similar looking pumps are available, they do not have the features of our SNOW Performane pumps.
Double EPDM seals ensure durability and higher pressure. Proprietary internal wiring offers lower power consumption than similar looking pumps. Integrated thermal protection circuitry allows the pump to operate constantly without damaging pump internals.
Hyper-Sonic Injection nozzles
The SNOW Performance HyperSonic atomiser nozzle is the world's best-selling and most advanced water/alcohol injection nozzle. The liquid is swirled inside the patented 2-chamber nozzle at supersonic speed before being forced through the Venturi orifice. This creates droplets or mists as fine as 20µ (microns) with enormous cooling potential.
The principle of evaporative cooling is a highly efficient technology and effectively reduces the intake or charge air temperature. Likewise, evaporation processes within the engine reduce the thermal load.
3l Reservoir with Fluid Level Switch
Boost Cooler water injection 3l tank with separate level indicator and warning LED (orange) for installation in the vehicle interior. With the "reserve light" you can be sure never to operate your water-methanol injection without sufficient fluid. Completely incl. connection for 1/4" pressure line.
To extend the range of the water injection, you can upgrade this system to a tank with a capacity of 9.5l or 26.5l. To do this, simply configure the desired tank size.
SCOPE OF DELIVERY
- 1 x High Pressure Diaphragm EPDM Pump, 300 PSI UHO
- 1 x Stage 3 TD 2D LCD Controller
- 1 x Dual Stage Upgrade
- 2 x HyperSonic Water-Methanol Nozzle incl. filter
- 1 x 3l Boost Cooler Water-Methanol Injection Reservoir
- 1 x Low level indicator (includes LED)
- 1 x ProLine stainless steel braided line (1x 30cm, 1x60cm, 1x1.5m)
- 2 x Nozzle Holder, 90°, Aluminium hard-anondized/li>
- 1 x Installation material and all necessary ProLine fittings
- 1 x Installation instructions
Frequently asked questions
Why turbo / naturally aspirated engine achieves more power with the Boost Cooler?
The main problem of any internal combustion engine is the thermal load. In nearly all engines, the power is restricted by the temperature in the combustion chamber. If a certain temperature is exceeded, uncontrolled combustion ("knocking") occurs. 
Uncontrolled combustions results in a massive loss of power and engine damage. In a turbo engine, this problem is compounded even further. The intake of the turbo engine heats up strongly in the turbine (through compression and heat transfer of the exhaust gases) and the thermal limit is quickly reached. In conventional turbo engines, one tries to get this problem solved with the help of intercoolers.
The performance of a turbocharged engine is therefore directly dependent on the efficiency of the intercooler, as well as the cooling rate of the intake and charge air. The efficiency of intercoolers, however, is constrained by the ambient temperature and the maximum size of tight physical limits. An increase in boost pressure no longer produces more power and the damage to the engine is virtually inevitable. This issue can be solved using the Boost Cooler waterinjection concept. You can ensure additional cooling of the heated intake air through the injection of a water / alcohol mixture. The great advantage of the Boost Cooler is that the cooling is virtually unlimited in physical terms. That is, if the intake air is too hot, simply increase the injection volume to achieve the required cooling degree. This unique advantage can help fully exploit the capacity of turbo engines and the engine power is not restricted by the thermal limits.
Does the Boost Cooler cause any damage to my engine?
No. At a relative humidity of 50% and ambient temperature of 25° C, a turbocharged engine consumes (2.0 l displacement, 1 bar boost pressure) approx. 160 ml of water per minute. For example, if a gasoline engine is used, the combusted air / fuel mixture consists of approximately 50% of water vapour and carbon dioxide. 
With the injection of 250 ml/ min of water per minute at full load, the Boost Cooler accounts for less than 1.6% of the exhaust gases Horror scenarios ("water hammer", rusting motors, etc.) that some of you might have read on the Internet tuning forums are only based on a lack of understanding of the technical writer or improper systems.
Study of Porsche Engineering (excerpt): “The technology of water injection into the intake manifold provides significant potential. This technology can use a stoichiometric air-fuel ratio in the entire operating area and an optimal ignition timing to increase the efficiency of the engine. In addition to a further reduction in fuel consumption, this effect also reduces the compression work so that the engine displacement can be further reduced."
Source: Porsche Engineering Magazine, Issue 01/2013
Where can I mount my reservoir and pump?
The pump needs to be within about 60cm (hose length) of the reservoir, and as low or lower than the base of the reservoir. It is a “pusher” pump, not a “puller” pump. In the engine bay, the reservoir and pump can be placed almost anywhere, as long as they are not very close to exhaust heat, or in the path of debris from the road. Be sure that the pump is mounted at the same level or below the reservoir and that the reservoir is not located higher than the nozzle. If the reservoir must be located higher than the nozzle, a solenoid upgrade is required to prevent gravity feed. Trunk mounting is also fine, but the pump needs to be close to the reservoir and gravity fed. Lengths of 6-7m of tubing to the nozzle are fine.
Which mixing ratio and what kind of water are used?
Use distilled or demineralised water only. Distilled water is available in any hardware store (about € 1.50 for 5 litres) or gas station. Of course you can also use clean tap water when nothing else is available at the moment. Use methanol or bio-ethanol (approx. 45 € per 30 litres, including shipping), or isopropanol. A 50/50 ratio is recommended. This has been demonstrated to be the best for charge/air cooling, excellent detonation control, and safety.
Do NOT use E85 or any other fluid with gasoline mixed in. It will destroy the fluid delivery part of your Boost Cooler and instantly void the warranty.
How much range will a tank of Water/Methanol provide?
This depends on a number of variables. HP, injection system, settings, driving style, etc. For most gasoline engines in the 200-250hp range, the standard 3l tank will last around a tank of gasoline when driving on the road. Diesels use more fluid than a gasoline application, and are in heavier load states more often. Due to the higher consumption of liquid in turbodiesels and/or powerful gasoline cars, we recommend at least our 9.5 l or 26.5 l trunk mounting kit as needed.
Where can I mount the nozzle?
The best placement of the nozzles is in the area around the inlet to the intake manifold or virtually anywhere on the pipe leading from the intercooler to the intake manifold. The nozzles can be placed at any position on the tube, so long as they are pointing at a 90 degree angle to the direction of airflow. The nozzles can be placed in a series or right next to each other.
There is enough heat and velocity and flow through the pipe under boost to absorb the water/methanol regardless of the nozzle positions relative to each other. Placement before the intercooler or turbo(s) is not recommended. Cooling is not improved. Never mount an injector nozzle before a turbocharger compressor. Studies performed by SAAB, concluded that pre-turbo injection will over time cause cavitation on the turbo wheel leading edges.
Do I need to activate the Boost Cooler in some way?
The Boost Cooler will activate automatically. Depending on the system, it activates after receiving a pre-set boost pressure or engine load signal, and then starts injecting in a load-dependent manner.
Do I need an intercooler with the Boost Cooler?
Up to approximately 2bar of boost, water/methanol injection (using 50% methanol) will provide all the density increase/detonation control needed in most applications. Of course, intercooling and water/methanol injection would provide even greater benefits, especially beyond 2bar of boost.
Most air-to-air intercoolers are only 50-65% efficient. For example, with 0.75 bar of boost and the resulting 50°C air charge temperature increase, an intercooler reduces the air charge temperature only 25 degrees. Also, an intercooler will reduce boost 0.1-0.25bar on average.
 |
 |
| Installation inside the engine compartment |
VC-MAF Controller |
 |
 |
| Reservoir with 9l capacity inside the trunk |
LCD-Controller |
 |
Tunetec Performance
Berlin
|
|
Reinaldo Maloon
USA
|
| |
|
"...it´s unbelivable what the Boost Cooler does! We realized 520hp and 670Nm torque out of the RS4 by using the Boost Cooler!" |
"Incredible! After installing the Boost Cooler™, I can run 8 psi more boost and more timing with no knock!" |
|
|
Dougs Auto
USA
|
|
Simon W.
Schöllnach
|
| |
| "I can run 10° more timing! Now my Vortech supercharged Saleen runs like it should-huge seat of the pants difference!" |
"...your Boost Cooler is just awesome ! Power increases, temperature drops. Thats how tuning should be !" |
 |
Diesel Power
Mit dem Snow Performance Stage 3 Boost Cooler system wurde bei einem 1991er Dodge Cummings eine Leistung von 587PS erreicht.
|
 |
Diesel World Feature Truck
The Snow Performance MPG MAX® Boost Cooler® is installed on a Ford 6.4 Powerstroke with fantastic results! The editor is impressed because the results are better than promised.
|
| |
 |
Diesel World
Discussion of the Boost Cooler® MPG MAX® and how it positively affects fuel mileage.
|
 |
Diesel Tech
Diesel Tech installs the MPG MAX Boost Cooler to increase towing power, decrease EGTs and INCREASE FUEL MILEAGE!
|
| |
 |
Diesel Tech
Snow Performance im Produktführer als einziger Hersteller von Wassereinspritzungen empfohlen.
|
 |
8 Lug Tests the new MPG MAX
8 Lug Installs the new MPG MAX on a GM Duramax.
|
| |
 |
Diesel World
The newest issue of Diesel World has details on the SEMA International Media award won by Snow Performance as well as new prouduct info and an installation article on the new MPG-MAX system. The MPG-MAX provides better cooling, more power, and better fuel economy gains than any other water/methanol injection system available.
|
 |
Dresden-Breslau Rallye auf N-TV Sport
Rallye Dresden-Breslau - Abseits der Straße durch Sand, Schotter und Morast. Eine Abenteuer-Fahrt für Off-Roader. Die Redaktion von N-TV bestritt die Rallye in Zusammenarbeit mit Suzuki Deutschland und Snow Performance. Der Suzuki Jimny, mit einem 1.5l Turbodiesel Motor, ist dem Boost Cooler Stage 3 Diesel- LCD System ausgestattet worden.
|
| |
 |
Diesel Builder
The new Boost Cooler Stage 3 Diesel MPG-MAX system continues in the Snow Performance tradition of making more power, controlling EGTs, and reducing emissions but with the added benefit of maximizing your fuel economy. Check out the simple MPG-MAX installation and see how it compliments other power adders and increases fuel economy by 2-3 mpg.
|
 |
Diesel Power
Today´s turbo diesel trucks pull double duty as they get used as a work horse, daily driver, trailer puller, or play toy. George Wadeson´s ´06 1-ton Cummins is no exception and it sees it´s fair share of use whatever the reason may be. A Snow Performance Stage 3 Boost Cooler helps keep EGTs down while the 65 psi of turbo boost cranks out 1200+ ftlb of torque.
|
| |
 |
8 Lug Diesel Truck
Rodney Findley's Dodge diesel truck is an extreme audio and visual experience on wheels. Motivating the traveling entertainment booth is a hopped-up 5.9L Cummins with a long list of performance enhancing mods including a Stage 2 Boost Cooler system.
|
 |
Diesel World
Ralph Merwin's custom J-series Jeep pickup sports a 12 valve Cummins diesel engine that is enhanced by the Snow Performance Boost Cooler for more power and reduced EGTs. |
| |
 |
Diesel World
The Snow Performance Stage 3 Diesel Boost Cooler is installed on Bully Dog's custom 6.7L Cummins. Using Boost Juice, the truck pumped out an additional 103 hp and 289 ft-lbs of torque!
|
 |
Diesel Power
Diesel Power magazine suggests that water/methanol injection be one of the first 11 modifications that you do to your diesel truck.
|
| |
 |
Diesel Builder
Stacked Diablo Sport performance controllers plus the Boost Cooler deliver over 200 hp on Snow Performance's own '04 Cummins 3500 shop truck.
|
 |
Diesel Power
Build up coverage of the 11 second Project X Dodge Cummins diesel truck which features the Snow Performance Boost Cooler. |
| |
 |
Turbo Diesel Register
A double controller stacked 2004 Dodge Ram 5.9L Cummins pulls double duty as a daily driver and frequent work horse. Over 100 WHP is achieved with the Snow Performance Boost Cooler along with a host of other performance goodies.
Base-Horsepower: 279PS
==> Boost Cooler w/ 50% Methanol: 453hp ==> w/ 75% Methanol: 487hp!
|
 |
Diesel Power
Boost Cooler installation on a 2004 1-Ton Dodge Cummins with before and after dyno results. |
| |
 |
Trucks
A 2004 Ford F-350 receives a Snow Performance Boost Cooler and picks up over 50 whp. |
 |
Turbo Diesel Register
An in-depth article that takes the many benefits of water/methanol injection for a modern turbo diesel into consideration. |
