BOOST COOLER
FEATURES
AT A GLANCE
- Precise electronically controlled injection by means of fuel injection quantity and boost pressure
-
ProLine Version: High-quality steel braided lines and connection technology
- Dual Stage technology for maximum efficiency in all load ranges
- Higher boost pressure and/or more aggressive ignition without knocking combustion - additional power up to 25% possible.
- Octane booster, 116 octane racing fuel performance with regular gasoline
- Earlier ignition timing or boost pressure without knocking combustion.
- More power and torque with simultaneous reduction of the thermal load on engines that have already been modified, e.g. by chip tuning, NOS or LPG/autogas.
- Effective intake air cooling, compensation of power losses at higher outside temperatures
- Reduction of the specific fuel consumption.
- Deposit-free combustion chamber and intake tract, without formation of oil carbon.
- Easy installation
SNOW PERFORMANCE
BOOST COOLER
SYSTEMS
Boost Cooler water injection can achieve a power increase of up to 10-25% in turbo and supercharged engines without thermally overloading the engine. The intake air temperature is lowered by up to 60°C, the combustion chamber is cooled and the thermal load on already tuned engines is effectively reduced.
Water or water/alcohol (methanol or ethanol) is injected at high pressure into the hot charge air in a finely atomised form as soon as the desired starting charge pressure is reached. The evaporating liquid achieves an extremely effective charge air and intercooling, which, among other things, prevents uncontrolled combustion ("knocking"). The effect is demonstrably comparable with 116 octane racing petrol.
The Boost Cooler is unsurpassed in atomisation! The liquid is swirled inside the Hyper-Sonic atomiser nozzle at supersonic speed before being forced through the Venturi orifice. With the included Dual Stage Upgrade, 2 atomiser nozzles are used to inject as early as possible with the primary nozzle and to achieve maximum cooling and performance in peak loads with the switched-on 2nd nozzle.
STAGE 3 DI
CONTROLLER
The multi-award winning Boost Cooler Stage 3 DI control unit from SNOW Performance regulates the water or water-alcohol injection quantity progressively to the boost pressure and the fuel injection quantity (fuel pressure sensor signal). The desired start and full injection times are simply entered in the enclosed LCD screen. The controller then creates a 2D injection curve for the optimum injection quantity in all load ranges. By using boost pressure and the fuel pressure sensor signal, the Stage 3 controller enables very precise water-methanol injection quantity regulation.
In addition to the primary injector, another injector, independent of the primary injector, is optionally controlled by the control unit. - This ensures optimal use of cooling and power in all load ranges of the engine. The progressive injection of water or water/methanol based on the 2D mapping created is very precise and has a positive effect on cooling and engine performance over the widest possible engine load range.
Temperature and pressure resistant Boost Cooler steel flex braided line - ProLine Series. High-quality steel braided line for your Boost Cooler water injection of the ProLine series. - There is hardly a better line for use in water-methanol injection systems. Steel flex lines from SNOW Performance are quality products at the highest level. Ideally suited for high demands on appearance and safety, in motor sports as well as marine and aviation applications.
OPTIMAL FOR ALL
TURBOCHARGED
DIRECT INJECTION ENGINES
- Audi T/FSI: A1, A2, A3 / S3, A4, A5, A6, A8, TT, TTS
- Ford EcuBoost (e.g. Focus ST, RS, Lincoln MKC)
- BMW Turbo: 3 E90 335i, 3 F80, 4 F82, 5 F10 and newer models
- Peugeot/Citroën THP Engines
- Seat TFSI: Leon, Exeo; Skoda Fabia, Octavia.
- Opel Ecotec, SIDI, GTC
- VW TFSI/TSI: Eos, Golf 5+, Jetta 3+, Passat, Polo 6R, Tiguan
- VW Scirocco 137/138, T5, and many more
DUAL STAGE
TECHNOLOGY
The controller has a 2nd output to control a further, larger nozzle with a separate mapping ('Power Mode'). The connection of the 2nd nozzle can be set individually to achieve the best possible performance results.
PERFORMANCE
With the Boost Cooler, you can achieve a power increase of about 10-25%, even with already tuned turbo and supercharged engines. The optimum cooling compensates for typical power losses at higher outside temperatures. In addition, deposits in the combustion chamber and intake tract are reduced.
OPTIMAL COOLING
In contrast to a conventional intercooler, the intake air can be lowered below the ambient temperature! In addition to the outstanding efficiency, there is no loss of boost pressure as with conventional performance intercoolers. The Boost Cooler efficiently cools the intake air and combustion chamber temperature ("in-cylinder-cooling"). The addition of alcohol (preferably methanol or ethanol) additionally increases efficiency and counteracts lean running.
OCTANEBOOSTER
In combination with super gasoline (Euro 95) and a water/methanol mixture, you achieve a comparable effect as with 116-octane racing petrol. This also allows you to dispense with the considerably more expensive Shell "V-Power", "Ultimate 100", etc. and drive only with conventional super gas.
EASY INSTALLATION
To ensure a smooth installation, all connection materials are included in the scope of delivery of the system. The detailed installation instructions in English, with many illustrations and a clear structure, guide you step by step through the installation process.
LESS CONSUMPTION -
LESS CO2
The better efficiency improves fuel economy. As a rule, fuel savings are in the range of 5-15% depending on the vehicle, driving style and use (e.g. tractors).
LESS DEPOSITS IN THE COMBUSTION CHAMBER
The combustion chamber of your engine remains free of deposits, the heat dissipation, e.g. at the exhaust valves, remains optimal. Oil coking is reduced and prevented.
MOTORSPORTS KNOW-HOW
As an OE supplier and through its activities in a wide range of motorsport areas, SNOW Performance proves the quality and durability of the high-quality water injection systems "Made by SNOW PERFORMANCE".
High Pressure Pump
SNOW Performance 300 PSI UHO methanol injection pumps offer unmatched pressure, technology and reliability. All Boost Cooler diaphragm pumps are made in the USA and individually tested before shipping to ensure quality and reliability. Although similar looking pumps are available, they do not have the features of our SNOW Performane pumps.
Double EPDM seals ensure durability and higher pressure. Proprietary internal wiring offers lower power consumption than similar looking pumps. Integrated thermal protection circuitry allows the pump to operate constantly without damaging pump internals.
Hyper-Sonic Injection nozzles
The SNOW Performance HyperSonic atomiser nozzle is the world's best-selling and most advanced water/alcohol injection nozzle. The liquid is swirled inside the patented 2-chamber nozzle at supersonic speed before being forced through the Venturi orifice. This creates droplets or mists as fine as 20µ (microns) with enormous cooling potential.
The principle of evaporative cooling is a highly efficient technology and effectively reduces the intake or charge air temperature. Likewise, evaporation processes within the engine reduce the thermal load.
3l Reservoir with Fluid Level Switch
Boost Cooler water injection 3l tank with separate level indicator and warning LED (orange) for installation in the vehicle interior. With the "reserve light" you can be sure never to operate your water-methanol injection without sufficient fluid. Completely incl. connection for 1/4" pressure line.
To extend the range of the water injection, you can upgrade this system to a tank with a capacity of 9.5l or 26.5l. To do this, simply configure the desired tank size.
SCOPE OF DELIVERY
- 1 x High Pressure Diaphragm EPDM Pump, 300 PSI UHO
- 1 x Boost Cooler Stage 3 DI 2D LCD Controller
- 1 x Dual Stage Upgrade
- 2 x HyperSonic Water-Methanol Nozzle incl. filter
- 1 x 3l Boost Cooler Water-Methanol Injection Reservoir
- 1 x Low level indicator (includes LED)
- 1 x ProLine stainless steel braided line (1x 30cm, 1x60cm, 1x1.5m)
- 2 x Nozzle Holder, 90°, Aluminium hard-anondized/li>
- 1 x Installation material and all necessary ProLine fittings
- 1 x Installation instructions
Frequently asked questions
Why turbo / naturally aspirated engine achieves more power with the Boost Cooler?
The main problem of any internal combustion engine is the thermal load. In nearly all engines, the power is restricted by the temperature in the combustion chamber. If a certain temperature is exceeded, uncontrolled combustion ("knocking") occurs. 
Uncontrolled combustions results in a massive loss of power and engine damage. In a turbo engine, this problem is compounded even further. The intake of the turbo engine heats up strongly in the turbine (through compression and heat transfer of the exhaust gases) and the thermal limit is quickly reached. In conventional turbo engines, one tries to get this problem solved with the help of intercoolers.
The performance of a turbocharged engine is therefore directly dependent on the efficiency of the intercooler, as well as the cooling rate of the intake and charge air. The efficiency of intercoolers, however, is constrained by the ambient temperature and the maximum size of tight physical limits. An increase in boost pressure no longer produces more power and the damage to the engine is virtually inevitable. This issue can be solved using the Boost Cooler waterinjection concept. You can ensure additional cooling of the heated intake air through the injection of a water / alcohol mixture. The great advantage of the Boost Cooler is that the cooling is virtually unlimited in physical terms. That is, if the intake air is too hot, simply increase the injection volume to achieve the required cooling degree. This unique advantage can help fully exploit the capacity of turbo engines and the engine power is not restricted by the thermal limits.
Does the Boost Cooler cause any damage to my engine?
No. At a relative humidity of 50% and ambient temperature of 25° C, a turbocharged engine consumes (2.0 l displacement, 1 bar boost pressure) approx. 160 ml of water per minute. For example, if a gasoline engine is used, the combusted air / fuel mixture consists of approximately 50% of water vapour and carbon dioxide. 
With the injection of 250 ml/ min of water per minute at full load, the Boost Cooler accounts for less than 1.6% of the exhaust gases Horror scenarios ("water hammer", rusting motors, etc.) that some of you might have read on the Internet tuning forums are only based on a lack of understanding of the technical writer or improper systems.
Study of Porsche Engineering (excerpt): “The technology of water injection into the intake manifold provides significant potential. This technology can use a stoichiometric air-fuel ratio in the entire operating area and an optimal ignition timing to increase the efficiency of the engine. In addition to a further reduction in fuel consumption, this effect also reduces the compression work so that the engine displacement can be further reduced."
Source: Porsche Engineering Magazine, Issue 01/2013
Where can I mount my reservoir and pump?
The pump needs to be within about 60cm (hose length) of the reservoir, and as low or lower than the base of the reservoir. It is a “pusher” pump, not a “puller” pump. In the engine bay, the reservoir and pump can be placed almost anywhere, as long as they are not very close to exhaust heat, or in the path of debris from the road. Be sure that the pump is mounted at the same level or below the reservoir and that the reservoir is not located higher than the nozzle. If the reservoir must be located higher than the nozzle, a solenoid upgrade is required to prevent gravity feed. Trunk mounting is also fine, but the pump needs to be close to the reservoir and gravity fed. Lengths of 6-7m of tubing to the nozzle are fine.
Which mixing ratio and what kind of water are used?
Use distilled or demineralised water only. Distilled water is available in any hardware store (about € 1.50 for 5 litres) or gas station. Of course you can also use clean tap water when nothing else is available at the moment. Use methanol or bio-ethanol (approx. 45 € per 30 litres, including shipping), or isopropanol. A 50/50 ratio is recommended. This has been demonstrated to be the best for charge/air cooling, excellent detonation control, and safety.
Do NOT use E85 or any other fluid with gasoline mixed in. It will destroy the fluid delivery part of your Boost Cooler and instantly void the warranty.
How much range will a tank of Water/Methanol provide?
This depends on a number of variables. HP, injection system, settings, driving style, etc. For most gasoline engines in the 200-250hp range, the standard 3l tank will last around a tank of gasoline when driving on the road. Diesels use more fluid than a gasoline application, and are in heavier load states more often. Due to the higher consumption of liquid in turbodiesels and/or powerful gasoline cars, we recommend at least our 9.5 l or 26.5 l trunk mounting kit as needed.
Where can I mount the nozzle?
The best placement of the nozzles is in the area around the inlet to the intake manifold or virtually anywhere on the pipe leading from the intercooler to the intake manifold. The nozzles can be placed at any position on the tube, so long as they are pointing at a 90 degree angle to the direction of airflow. The nozzles can be placed in a series or right next to each other.
There is enough heat and velocity and flow through the pipe under boost to absorb the water/methanol regardless of the nozzle positions relative to each other. Placement before the intercooler or turbo(s) is not recommended. Cooling is not improved. Never mount an injector nozzle before a turbocharger compressor. Studies performed by SAAB, concluded that pre-turbo injection will over time cause cavitation on the turbo wheel leading edges.
Do I need to activate the Boost Cooler in some way?
The Boost Cooler will activate automatically. Depending on the system, it activates after receiving a pre-set boost pressure or engine load signal, and then starts injecting in a load-dependent manner.
Do I need an intercooler with the Boost Cooler?
Up to approximately 2bar of boost, water/methanol injection (using 50% methanol) will provide all the density increase/detonation control needed in most applications. Of course, intercooling and water/methanol injection would provide even greater benefits, especially beyond 2bar of boost.
Most air-to-air intercoolers are only 50-65% efficient. For example, with 0.75 bar of boost and the resulting 50°C air charge temperature increase, an intercooler reduces the air charge temperature only 25 degrees. Also, an intercooler will reduce boost 0.1-0.25bar on average.
 |
 |
| Installation inside the engine compartment |
VC-MAF Controller |
 |
 |
| Reservoir with 9l capacity inside the trunk |
LCD-Controller |
 |
Tunetec Performance
Berlin
|
|
Reinaldo Maloon
USA
|
| |
|
"...it´s unbelivable what the Boost Cooler does! We realized 520hp and 670Nm torque out of the RS4 by using the Boost Cooler!" |
"Incredible! After installing the Boost Cooler™, I can run 8 psi more boost and more timing with no knock!" |
|
|
Dougs Auto
USA
|
|
Simon W.
Schöllnach
|
| |
| "I can run 10° more timing! Now my Vortech supercharged Saleen runs like it should-huge seat of the pants difference!" |
"...your Boost Cooler is just awesome ! Power increases, temperature drops. Thats how tuning should be !" |
 |
Muscle Mustang & Fast Fords
Der Boost Cooler wurde in Verbindung mit normal-benzin getestet - und schlägt im Vergleichstest 116Oktan-Rennbenzin!
|
 |
Popular Hot Rodding
A comprehensive article by David Vizard regarding forced induction recommends using Snow Performance for chemical intercooling and octane enhancement. |
|
 |
Super Chevy
Snow Performance Boost Cooler(r) is a featured product in a supercharger information section as a great way to reduce intake air temps and increase power - race gas performance at pump gas prices!
|
 |
Super Chevy
Der Snow Performance Boost Cooler wurde in einem Motor mit Vortech-Kompressor verbaut. Bei nur 7.7psi Ladedruck wurden standfeste 710PS erzielt.
|
|
 |
Mustang Monthly
Snow Performance Boost Cooler(r) is a featured product in a buyers guide as a proven way to increase octane and power on naturally aspirate, high-compression engines. Increase fuel efficiency and run low-grade gasoline while improving performance.
|
 |
DSPort
Part II of "Chemical Romance" series highlights the benefits of the Snow Performance Boost Cooler®. With gains of over 120 whp, the Boost Cooler® supports the same horsepower level as expensive race gas but with even better cooling and detonation control. |
|
 |
Hot Boat
Forced induction guru Dustin Whipple of Whipple Superchargers recommends the Snow Performance Boost Cooler® for a blown Mercury boat mo
|
 |
Nissan Sport
A Stage 2 MAF Boost Cooler® is used to provide additional detonation control on a naturally aspirated Nissan QR25 engine with an astounding 12.5:1 compression ratio. Full ignition timing can now be realized while still using pump gas with an octane boost provided by water/methanol injection. |
|
 |
Modified Mag
Scott VanderHeide´s Boost Cooler assisted STi dukes it out in an Evo vs. STi match-up. See what the performance judges have to say about this super STi. |
 |
Peroformance Business
Performance Business interviews Snow Performance founder, President, and CEO, Matt Snow. Matt provides some insight on the modest start of his company as well as its exponential growth over the past seven years. |
|
 |
5.0 Mustang & Super Fords
The Shelby GT 500 Mustang comes well equipped to make some mean power straight from the factory. With an assortment of go fast goodies including a Snow Performance Boost Cooler, we take mean to a new level by incresing power by more than 60 whp! |
 |
Ford Builder
Supercoupes Unlimited and Dave Dalke team up to upgrade a '94 Thunderbird SC with a Snow Performance Boost Cooler. With a stealthy install this unsuspecting T-Bird packs a punch with an additional 53 hp thanks to a cooler air charge and additional detonation suppressant. |
|
 |
Modified Mag
SEMA show coverage that includes a brief look at what Snow Performane - The Water-Methanol Injection Experts - has to offer in the near future.
|
 |
Popular Hot Rodding
Popular Hot Rodding's supercharger issue is loaded with lots of forced induction features. Chris Downie's Magnacharged Chevy Silverado is not only blown but also enjoys a nitrous and water/methanol injected cocktail of power. |
|
 |
Mustangs & Fast Fords
Who wouldn't want maximum performance with peace of mind? The Snow Performance SafeInjection allows those who want to run on the ragged edge of performance to do so in complete saftey. Tied with an J&S Electronics SafeGuard, the SafeInjection unit will pull timing to prevent any chance of detonation if a loss in flow is ever detected. The water/methanol injection experts bring you the best in performance and safety.
|
 |
Modified Mag
William Updegrove's subtly modified Toyota Celica proves the old adage that less is more. His clean and simple approach is powered by a GReddy supercharged 1.8L that is liquid intercooled thanks to the Boost Cooler. |
|
 |
Modfied Mustangs
Matt Snow developed the best water/methanol injection available and decided to build a car specifically to showcase his products. The 4.6L SOHC three valve motor is turbo charged and detonation is keep at bay with the Snow Performance water/methanol injection system.
|
 |
GM High-Tech Performance
David Childress' daily driven '98 Pontiac Formula relies on the Snow Performance Boost Cooler to make 1000 whp and run 9 second ET's on pump gas. |
|
 |
Drag Racer
Nitrous injection innovator and N.O.S. company founder Mike Thermos discusses the advantages of running water/methanol injection with any nitrous injection setup.
|
 |
Modified Mustangs
Modified Mustangs recommends that the Snow Performance Boost Cooler be used to make more power safely for new Mustangs with aftermarket turbo kits. |
|
 |
Modified Mustangs
Modified Mustangs recommends that the Snow Performance Boost Cooler be used to make more power safely for new Mustangs with aftermarket turbo kits.
|
 |
Hot Rod Magazine
Coverage of a Snow Performance Boost Cooler kit that is installed on a ProCharger supercharged Z06 Corvette. |
|
 |
Hot Compact and Imports
As impressive as the Jackson Racing supercharger is, it is limited by the fact that it doesn't offer any kind of intercooling to support higher boost levels. This is remedied by the Snow Performance Boost Cooler as it provides chemical intercooling and an octane boost. A mild B16A receives a healthy increase in power, cooling, and reliability.
|
 |
5.0 Mustang & Super Fords
With a Max Power turbo kit, slammed stance, retro-Boss style graphics, and a Snow Performance Boost Cooler, Matt Snow's '05 Mustang is a screamin' "Snow Stormer." |
|
 |
Import Tuner
A Comptech supercharged Acura NSX is treated to Boost Cooler and tuning from HKS. With water/methanol injection and 5.5 psi of boost, the timing was turned up beyond what a stock n/a NSX normally runs.
|
 |
Mustangs & Fast Fords
Since the Mustang had been tuned using race fuel, we had to make several runs to tune it for pump gas before we would be able to start adjusting the Boost Cooler. While 493 rwhp on 93-octane pump gas is nothing to be ashamed of, the Boost Cooler eclipsed that by 78 hp for a total of 571 rwhp. Torque also increased from 477 to 516 lb-ft |
|
 |
High Performance Pontiac
Product review of the Snow Performance Gas Stage 2 GM MAF Boost Cooler. |
 |
Mustangs & Fast Fords
A double dose of water/methanol is just the thing needed for an Acura Integra and Mitsubishi Lancer Evolution VIII. With some chemical intercooling and the SafeInjection system monitoring flow, the boost can safely be cranked up to make more power. |
|
 |
Camaro Performers
Product review of the Snow Performance Gas Stage 2 GM MAF Boost Cooler. |
 |
Auto Bild Sportscars
6 Autos, die eines verbindet: Ihre Leistung kennt keine elektronischen Grenzen. Mit insgesamt 9506 PS stellen sie in Nardo mit Nachdruck unter Beweis: Bei 250 km/h muss lange nicht Schluss sein. |
|
 |
Audi Tuning
Ausgabe 04/2006 - "Audi RS4 Powertricks"
Boost Cooler Stage 2-VC25 Audi RS4 Digi-Tec
Artikel über Leistungstricks bei einem Audi RS4 - vorgestellt wurde ein von DigiTec modifizierter RS4 mit ca. 500PS und Boost Cooler System< |
 |
High Performance Pontiac
Product review of the Snow Performance Gas Stage 2 GM MAF Boost Cooler. |
|
 |
Ford Truck Performance
A JLP prepped Lightning takes it a step further with a Snow Performance water/methanol injection system. |
 |
5.0 Mustang & Super Fords
The Snow Performance Boost Cooler is installed on a well warmed over 2004 SVT Cobra. |
|
 |
Chevy High Performance
A Magnacharger supercharged Chevy Silverado SS pickup uses a Boost Cooler water/methanol injection kit to reduce intake air temperatures and make more power. |
|
|
|
|
|
|
